Connection refused (61)

[Teno Deuter]

actually I did define the staic IP address already and now I get the
following in the roundcube error log:

STARTTLS failed ()
Invalid response code received from server (-1)
Failed to write to socket: unknown error ()
SMTP Error: Authentication failure: STARTTLS failed (Code: )



On Thu, Jul 12, 2018 at 12:40 AM, Larry Rosenman <larryrtx at gmail.com> wrote:
> Yes, or, add another block of lines with lo (or lo0) depending on what your kernel uses for loopback in place of the $egress_int parameter to get it to listen on  127.0.0.1 as well.
>
>
>
> --
> Larry Rosenman                     http://www.lerctr.org/~ler
> Phone: +1 214-642-9640             E-Mail: larryrtx at gmail.com
> US Mail: 5708 Sabbia Drive, Round Rock, TX 78665-2106
>
> On 7/11/18, 5:38 PM, "Teno Deuter" <gvgter at googlemail.com> wrote:
>
>     shows the static IP address of the box. You mean to put that address
>     in the config file?
>
>     On Thu, Jul 12, 2018 at 12:36 AM, Larry Rosenman <larryrtx at gmail.com> wrote:
>     > What does ifconfig nfe0 show for inet?
>     >
>     >
>     > --
>     > Larry Rosenman                     http://www.lerctr.org/~ler
>     > Phone: +1 214-642-9640             E-Mail: larryrtx at gmail.com
>     > US Mail: 5708 Sabbia Drive, Round Rock, TX 78665-2106
>     >
>     > On 7/11/18, 5:35 PM, "Teno Deuter" <gvgter at googlemail.com> wrote:
>     >
>     >     but:
>     >
>     >     egress_int="nfe0"
>     >
>     >     you mean to put this value?
>     >
>     >     On Thu, Jul 12, 2018 at 12:30 AM, Larry Rosenman <larryrtx at gmail.com> wrote:
>     >     > $egress_int is NOT 127.0.0.1.
>     >     >
>     >     > Change roundcube to use the same address.
>     >     >
>     >     >
>     >     > --
>     >     > Larry Rosenman                     http://www.lerctr.org/~ler
>     >     > Phone: +1 214-642-9640             E-Mail: larryrtx at gmail.com
>     >     > US Mail: 5708 Sabbia Drive, Round Rock, TX 78665-2106
>     >     >
>     >     > On 7/11/18, 5:26 PM, "Teno Deuter" <gvgter at googlemail.com> wrote:
>     >     >
>     >     >     this is what I have now in my smptd conf file:
>     >     >
>     >     >     listen on $egress_int pki server.pki tls-require hostname [domain]
>     >     >     listen on $egress_int pki server.pki port 587 tls-require auth hostname [domain]
>     >     >     listen on $egress_int pki server.pki smtps auth hostname [domain]
>     >     >
>     >     >     but the problem is still there :(
>     >     >
>     >     >     On Thu, Jul 12, 2018 at 12:04 AM, Larry Rosenman <larryrtx at gmail.com> wrote:
>     >     >     > ---
>     >     >     > /etc/smtpd/smtpd.conf
>     >     >     > pki mx.domain.tld certificate  "/etc/smtpd/tls/smtpd.crt"
>     >     >     > pki mx.domain.tld key          "/etc/smtpd/tls/smtpd.key"
>     >     >     >
>     >     >     > table creds                    "/etc/smtpd/creds"
>     >     >     > table vdoms                    "/etc/smtpd/vdoms"
>     >     >     > table vusers                   "/etc/smtpd/vusers"
>     >     >     >
>     >     >     > listen on eth0 tls pki mx.domain.tld
>     >     >     > listen on eth0 port 587 tls-require pki mx.domain.tld auth <creds>
>     >     >     >
>     >     >     > accept from any for domain <vdoms> virtual <vusers> deliver to mbox
>     >     >     > accept for any relay
>     >     >     > ----
>     >     >     > Add a:
>     >     >     > listen on lo  port 587 tls-require pki mx.domain.tld auth <creds>
>     >     >     >
>     >     >     >
>     >     >     > --
>     >     >     > Larry Rosenman                     http://www.lerctr.org/~ler
>     >     >     > Phone: +1 214-642-9640             E-Mail: larryrtx at gmail.com
>     >     >     > US Mail: 5708 Sabbia Drive, Round Rock, TX 78665-2106
>     >     >     >
>     >     >     > On 7/11/18, 5:00 PM, "dovecot on behalf of Teno Deuter" <dovecot-bounces at dovecot.org on behalf of gvgter at googlemail.com> wrote:
>     >     >     >
>     >     >     >     produces an empty result!
>     >     >     >
>     >     >     >     On Wed, Jul 11, 2018 at 11:57 PM, Richard
>     >     >     >     <inbound-dovecot at listmail.innovate.net> wrote:
>     >     >     >     > what does the output of:
>     >     >     >     >
>     >     >     >     >     netstat -n | grep :587
>     >     >     >     >
>     >     >     >     > run as root, show you? the -p will give the program and pid.
>     >     >     >     >
>     >     >     >     >
>     >     >     >     >
>     >     >     >     >> Date: Wednesday, July 11, 2018 21:51:09 +0000
>     >     >     >     >> From: Larry Rosenman <larryrtx at gmail.com>
>     >     >     >     >>
>     >     >     >     >> Yep, you (probably) need to configure openSMTPD to listen on 587
>     >     >     >     >>
>     >     >     >     >> (I run exim, so I can't help with that).
>     >     >     >     >
>     >     >     >     >
>     >     >     >
>     >     >
>     >
>